Netgear FVL328 Firmware 2.0 R07

• 
• Download Netgear FVL328 Firmware 2.0 R07

Netgear FVL328 Firmware 2.0 R07 description

OSSupport:Windows Size:1.3 MB
Netgear FVL328 Firmware 2.0 R07 note describes enhancements and bug fixes in the FVL328 Release Version 2.0_07 software. The enhancements and fixes are those added since Release Version 2.0_02.Note: A factory reset is required after upgrading (unless upgrading from Version 2.0 Release 02 or later and having performed a factory reset after upgrading). Please see instructions below.Modifications and Bug FixesVersion 2.0_07 1. Fixed a problem where remote management access could be lost after a period of time 2. Fixed a problem where a local server using port 5050 would not function properly 3. Can now accept fragmented IKE packets 4. Fixed a problem with using domain names in the VPN IPSec policy 5. Fixed a problem where Daylight Saving start time in Egypt was wrong 6. Fixed a problem where Daylight Saving end time was wrong in Chile 7. Added a checkbox to enable use of a short retry time with ngDDNSVersions 2.0_02 through 2.0_06 1. NTP logging has been moved to the Other connections and traffic to Netgear FVL328 Firmware 2.0 R07 Router category and is enabled by checking this checkbox 2. An issue where debug code could result in remote FQDN resolution to a test address in the absence of a valid address was resolved by removing the debug code 3. In the Services menu, if the finish port is left blank, the service is now correctly created assuming the service applies only to the start port 4. Fixed a problem where, for certain time zones including GMT, after checking the Automatically adjust for Daylight Savings Time check box and applying Netgear FVL328 Firmware 2.0 R07, the checkbox would become unchecked 5. Fixed a problem in LAN to LAN mode where the remote sides DNS was not obtained, so a DNS had to be entered manually. 6. Fixed problems with access to various Web sites 7. Fixed issue which had resulted in bogus logs including First TCP Packet not SYN, TCP preconnect traffic, etc 8. Fixed a problem with PPPoE idle timeout 9. Fixed a problem where the IKE packet could be sent incorrectly in PPPoE mode 10. There is now a Drop button on the VPN status page for Manual policies 11. Fixed a problem with parallel Trace Route using Netlab95 12. Improved operation of automatic Daylight Savings Time adjustment on the Logs page 13. Dyndns addresses are now updated automatically after 28 days 14. Fixed a problem where logs would not be sent out when full even though email set to Daily 15. Fixed a problem with inbound VPN connections when NAT off 16. Increased FQDN character limit to 128 characters 17. Fixed a problem where massive FTP transfers could fail 18. Fixed a problem where LAN client PCs couldnt get an IP address if NAT off and PPPoE/PPTP WAN connection type 19. Fixed a problem where RIP packets were not broadcast if PPPoE WAN connection type 20. When logging out, user is no longer asked for passwordKnown Issues 1. If the VPN Wizard is used to configure a gateway to gateway tunnel, and then a client to gateway policy is manually added, the client to gateway policy will become the first policy and Internet will not be accessible (all the traffic goes into the client to gateway tunnel). Workaround is to use the VPN Wizard to set up both policies.To Upgrade You can upgrade by using the Configuration Manager. 1. Download and unzip the upgrade file from the link below to a convenient place such as your desktop. 2. Using a browser, login to the router as admin. 3. Under Maintenance, click Router Upgrade. 4. Click Browse and locate the upgrade file fvl328_2007.img. 5. Click Upload. 6. Wait for the router to reboot and the TEST LED to turn off. 7. Power cycle the router. NOTE: Unless you are upgrading from version 2.0_02 or later, this version requires clearing to Factory Defaults after upgrading. Before upgrading from an earlier version, write down all of your configuration information. After upgrading, clear the old configuration by pressing the Factory Defaults pushbutton on the rear panel until the Test LED blinks (about 10 seconds). Then reenter your configuration information manually.NETGEAR has been a worldwide provider of technologically advanced, branded networking products since 1996. Our mission is to be the preferred customer-driven provider of innovative networking solutions for small businesses and homes.

Netgear FVL328 Firmware 2.0 R07 Tag: